Welcome to visit us!

[email protected]

carbon fiber laser cutting steels

carbon fiber laser cutting steels, Fiber Laser Cutting Metal Techniques | IPG Photonics50 x 25 mm Rectangular Profile Cutting Cutting 10 mm Carbon Steel with 4.5 kW Fiber Laser Flat Sheet Cutting with LaserCube Cutting Inspection and Analysis Rotary Cutting with the LaserCube Each cutting process is highly dependent on material type and thickness and required processing speed, edge quality and kerf width.

Whatever your requirements about carbon fiber laser cutting steels, you 'll find the perfect service-oriented solution to match your specific needs with our help. We are here for your questions anytime 24/7, welcome your consultation.

Online Chat [email protected]
  • Carbon Fiber Laser Cutting and Marking Carbon Fiber ULS

    Carbon Fiber Overview. Carbon fiber, which is also known as Carbon Fiber Reinforced Polymer or CFRP, consists of long strands of carbon reinforcing material, typically woven together to form a fabric and then bound together by a polymer matrix material. Laser cutting carbon fiber can be done with either a CO 2 laser or a fiber laser,

    Read More
  • An Engineer’s Guide to Laser Cutting > ENGINEERING

    Apr 16, 2018 · The two most common types of laser cutting machines are fiber laser and CO 2. CO 2 lasers use an electromagnetically stimulated gas—typically, a mixture of carbon dioxide, nitrogen and sometimes hydrogen, xenon or helium—as their active laser medium.

    Read More
  • High Power Laser Cutting of Steel PlatesHeat Affected

    The thermal effect of CO2 high power laser cutting on cut surface of steel plates is investigated. The effect of the input laser cutting parameters on the melted zone depth (MZ), the heat affected zone depth (HAZ), and the microhardness beneath the cut surface is analyzed.

    Read More
  • Nitrogen vs. OxygenWhich Should You Use to Cut Steel?

    To make the most cost effective decision on the choice between these assist gases, several important factors must be weighed. However, laser cutting of steel with nitrogen is not limited to thin material. Nitrogen can be used as an assist gas for thicker steels, with the maximum thickness depending on the available laser power.

    Read More
  • Southwest Waterjet And Laser Laser Cutting & Waterjet

    The machine is so precise, in fact, that when cutting something like a granite tile out of a slab of stone, the edge that is cut is the finished edge. This means there is no additionally sanding or filing required. Contact us at Southwest Waterjet and Laser for all of your granite cutting needs.

    Read More
  • Laser Cutting Service Online Quote

    Xometry's Manufacturing Partner Network offers both Fiber and CO2 lasers that can cut a number of materials including mild steel, stainless steel, aluminum, copper, brass, and exotic alloys. CO2 (carbon dioxide) laser excels at cutting, engraving, and boring metals,

    Read More
  • Carbon Fiber Laser Cutting Machine For Metal

    It will stop cutting when colliding plate. The safety following module reduces accident rate and improves cutting performance.Carbon Fiber Laser Cutting Machine For Metal is suitable for cutting carbon steel, stainless steel, aluminum, brass and alloy metal materials. Features

    Read More
  • Flatbed Fiber Laser Cutting Machine IPG Photonics

    LaserCube Fiber Laser Cutting Machine. Utilizing YLS fiber lasers up to 4 kW average power and IPG cutting head technology, the LaserCube handles metal sheets up to 48 × 48 inches (1250 x 1250 mm). Working on a variety of materials including steel, aluminum, brass, copper, titanium and alloys, the LaserCube provides superior cutting performance

    Read More
  • High Power Laser Cutting of Steel PlatesHeat Affected

    The thermal effect of CO2 high power laser cutting on cut surface of steel plates is investigated. The effect of the input laser cutting parameters on the melted zone depth (MZ), the heat affected zone depth (HAZ), and the microhardness beneath the cut surface is analyzed.

    Read More
  • Southwest Waterjet And Laser Laser Cutting & Waterjet

    The machine is so precise, in fact, that when cutting something like a granite tile out of a slab of stone, the edge that is cut is the finished edge. This means there is no additionally sanding or filing required. Contact us at Southwest Waterjet and Laser for all of your granite cutting needs.

    Read More
  • Laser Cutting Carbon Fiber Reinforced Polymer Powerlase

    Laser Cutting Carbon Fiber Reinforced Polymer (CFRP) The UV or green wavelengths absorb we on the carbon fibres and binder material alike. The pulses lasting only a few tens of nanoseconds with peak power of ~100kW cut the fibres and material before any heat dissipates into the bulk material. Therefore cuts with minimum heat affected zone and kerf can be achieved.

    Read More
  • Laser cutting

    Standard roughness Rz increases with the sheet thickness, but decreases with laser power and cutting speed. When cutting low carbon steel with laser power of 800 W, standard roughness Rz is 10 μm for sheet thickness of 1 mm, 20 μm for 3 mm, and 25 μm for 6 mm.

    Read More
  • Laser Cutting Carbon Fiber Reinforced Polymer Powerlase

    Laser Cutting Carbon Fiber Reinforced Polymer (CFRP) The UV or green wavelengths absorb we on the carbon fibres and binder material alike. The pulses lasting only a few tens of nanoseconds with peak power of ~100kW cut the fibres and material before any heat dissipates into the bulk material. Therefore cuts with minimum heat affected zone and kerf can be achieved.

    Read More
  • How to Cut Carbon Fiber DragonPlate

    Cutting Carbon Fiber with a Laser Cutter Do not use a laser cutter as it will not work any carbon fiber. The laser melts the epoxy much faster than it can have an impact on the carbon fibers. This results in a very poor cut line and very few broken fibers.

    Read More
  • Laser cutting

    Laser cutting. When cutting low carbon steel with laser power of 800 W, standard roughness Rz is 10 μm for sheet thickness of 1 mm, 20 μm for 3 mm, and 25 μm for 6 mm. Wheresteel sheet thickness in mm; laser power in kW (some new laser cutters have laser power of 4 kW); cutting speed in meters per minute .

    Read More
  • Full Spectrum Laser Lasers for Cutting and Engraving

    Flatbed Fiber Laser. Cut up to 5'x10' sheet metal. 500W Fiber laser cuts through 1/4" (6mm) carbon steel, 4mm stainless steel, 2mm aluminum. Laser is contained within fiber optic cable (no optics to adjust) Ultra rapid, highly precise closed loop servo motors. Virtually no maintenance. Starting at $130,000.

    Read More
  • Five Tips for Working with Carbon Fiber Protech Composites

    Cutting Carbon Fiber Laminate Carbon fiber sheets can be cut with standard tools, ranging from scissors and razor knives for thinner sheets, to abrasive cutting wheels and dremel tools. For cutting many carbon fiber veneer sheets, we recommend the use of carbide tools, abrasive type cutters, or

    Read More
  • SS Cutting XTLASER

    Fiber laser cutting machine is a very popular and high efficiency machine for cutting metal, it can cut different kind metals, like stainless steel, carbon steel,  aluminum sheet, brass, copper,  galvanized plate, etc, so now it’s widely used in the industries of kitchen ware, steel furniture, elevator,auto parts and  so on.

    Read More

What Can I Do For You?

Hot Products

Steel Materials

New Products

Copyright © 2015.BTN STEEL Co., ltd. All rights reserved.